124, Vacuum

When was the last time you knocked one of your vacuum lines off around the oil filter housing, only to discover when you tried to reattached it that the fittings were swollen and would just not stay connected? This is a L shaped fitting that fits 115, 116, 123, and 126 chassis.

When was the last time you knocked one of your vacuum lines off around the oil filter housing, only to discover when you tried to reattached it that the fittings or hose were swollen and would just not stay connected? Here is some extra vacuum hose to fix your problem. Fits 115, 116, 123, and 126 chassis.

Comes in a 2 meter roll.

This is my favorite set of tweezers for helping to hold small parts in place for assembly. The wide ones are particularly helpful when a second hand is needed to hold a small bolt or screw in place. Comes with seven different tweezers as shown. Good for car work. Not good for pulling hair!

Applies to testing vacuum problems and bleeding brakes on all chassis Pre 1960, 190SL, 110, 111, 112, 113, 114, 115, 108, 109, 107, 116, 123, 126, 201 and 124 chassis. You have asked for it so we decided to deliver. Here is my recommendation for the best vacuum test pump you can buy for the money. Over the years Ive used three different types of vacuum hand pump testers and out of these three this one has proven to be the best all around. It has the best feel of the grip when pumping, the greatest amount of vacuum created at each pump stroke and the highest durability. This unit has a brass body and is very well built. Must better than the Mighty Vac plastic units.

New Vacuum testing gauge with fittings in hard plastic case. This is a very nice gauge will a 4 inch diameter face that is easy to read from a distance. Use this on your diesel to test for vacuum pump operation and to isolate major problem areas. Use this on your gas engine to check for intake leaks, valve timing problems, ignition timing, and fuel injection problems. Can also test low pressure fuel pumps. Gauge reads to 28 inch Hg Vacuum and 0-10 psig pressure.

PLEASE NOTE: This gauge can only test for a working vacuum source. It cannot test for vacuum leaks in individual vacuum components, such as door lock actuators, fuel shut off valve, climate control actuators, etc. To isolate leaks in individual vacuum components you will need a hand pump tester.

This is a brand new Genuine Mercedes 3 way Vacuum change over valve. It is located in the engine compartment. It fits almost every chassis Mercedes, both gas and diesel models, from the 60’s up through the late 90’s. It has multiple uses such as EGR valve function, transmission control, etc.

We have finally found a source for hard plastic vacuum line! This is genuine Mercedes Benz brand line and is transparent with a yellow stripe. It is found on all 107 116 123 124 126 201 chassis. It is a little more expensive than the other hard vacuum line we carry, so we are selling it in a ONE METER length. It can be used anywhere in the engine compartment.

We have finally found a source for the engine compartment hard vacuum line! This vacuum line is white and is 4 mm in size. It is used on all 107 108 109 110 111 113 114 115 116 123 124 126 chassis. You can use it to replace any hard vacuum line on the engine. We are selling it in a 3 meter roll, more than enough to do any replacement job, because we got it at such a good price. It is made by Cohline and is very good quality.

This $25 gift certificate can be used up to one year from date of purchase to be applied toward the purchase any item or items on our website . The certificate will be mailed with an individual certificate number for identification purposes. All the recipient needs to do with it is call in with his order and give us the certificate number.

If you desire a certificate greater than $25.00 can order more than one of these (in $25 increments) or you can call 800-513-5797 with any specific amount you want. This is a great gift to give to a Mercedes enthusiast. There is no charge for mailing a certificate.