110/111/112 Sedan, Tools and General Hardware

This is the tool I love to use when troubleshooting engine operating temperature problems. You can stand back and aim the beam right on a spot on the radiator or engine to get an exact temperature reading. This can indicate whether or not your radiator is plugged and confirm if your temperature gauge is accurate or not.

If you are running SVO it can give you accurate readings of the temperature of your oil - both during filtering and coming out of your boost heater.

Features:

NEW LOCTITE PRODUCT - AUGUST PROMO! If you have read very many of my manuals and instructions you already know how much I detest Silicone Gasket Sealant. I know there are places for silicone (ie bath tub caulking, etc), but it should not be used on internal combustion engines!

Applies to all Mercedes, PON FIN Pre 1960, 190SL, 110, 111, 112, 113, 114, 115, 108, 109, 107, 116, 123, 126, 201, and 124 chassis. Here is a kit you will love to have around the shop. If you don't like using those poor quality US hose clamps (the kind that cut into the hose) then here is a chance to have spare quality (no nick) hose clamps for those fuel and coolant related repairs. Kit comes with  large size hose clamp. Hose clamp size is 32-50/9.

Applies to all Mercedes, PON FIN Pre 1960, 190SL, 110, 111, 112, 113, 114, 115, 108, 109, 107, 116, 123, 126, 201, and 124 chassis. Here is a kit you will love to have around the shop. If you don't like using those poor quality US hose clamps (the kind that cut into the hose) then here is a chance to have spare quality (no nick) hose clamps for those fuel and coolant related repairs. Kit comes with 10 medium size hose clamp. Hose clamp size is 16-27/9.

Kent has packaged together four of his most popular signature series products that will allow you to service, overhaul and tune your diesel fuel injectors yourself. All together these are key to helping you understand how your fuel injectors work, how to inspect and clean them, how to install new performance Monark injector nozzles, and how to balance tune them for maximum power and fuel effeciency.

These include the following items: Click on each one to read more.

Fuel Injector Pressure Bench Tester 

Diesel Injector Cleaning and Testing Procedures 

Diesel Injector Cleaning Brass Tool Kit 

These thin shim washers can be added to an existing injector shim to meet the thickness required to increase release pressure. Buy using a thicker shim along with 1 to 3 thin shims you will be able to make a number of different thicknesses within the 0,20 mm range. This kit contains six each of thin 0,20 mm washers.

These thin shim washers can be added to an existing injector shim to meet the thickness required to increase release pressure. Buy using a thicker shim along with 1 to 3 thin shims you will be able to make a number of different thicknesses within the 0,10 mm range. This kit contains six each of super thin 0,10 mm washers

If you are adjusting your injectors and your pressure reading is low you may only have to add one or two of the thin washers to bring the pressure up to spec. If your pressure reading is too high you will need to go down in thickness by choosing a think shim you have available and adding 1 or 2 thin (or any multiple you like) ones to build the thickness required. We also supply thin washer sets in 0,05 and 0,20 mm sizes.

These thin shim washers can be added to an existing injector shim to meet the thickness required to increase release pressure. Buy using a thicker shim along with 1 to 3 thin shims you will be able to make a number of different thicknesses within the 0,05 mm range. This kit contains six each of super thin 0,05 mm washers

If you are adjusting your injectors and your pressure reading is low you may only have to add one or two of the thin washers to bring the pressure up to spec. If your pressure reading is too high you will need to go down in thickness by choosing a think shim you have available and adding 1 or 2 thin (or any multiple you like) ones to build the thickness required. We also supply thin washer sets in 0,10 and 0,20 mm sizes.

One of the more challenging aspects of adjusting the release pressures on your diesel fuel injectors is finding the exact thickness shim washer you need to make the proper spring pressure adjustment. If you try to do it with just one shim per injector you end up needing a large assortment of all sizes of shims ranging from 0,80 mm to 1,95 mm. And knowing Murphy’s law all too well, you will end up needing the shim size that you do not have.

This is a 3 piece scribe and pick tool set - great for marking aluminum and steel.

Heat shrink tubing is very handing to have if you are doing any wire connections or splicing. This tubing can go over the splice or solder joint and when heat is applied from a heat gun it will shrink right down tight to the joint and protect it from shorts and corrosion.

This circuit tester has a long 7 inch point to get into hard to reach places. Accordion cord extends up to 12 feet! Wow!

This is a set of metric nut drivers. It come in 7 different handy sizes and is even color coded. Sizes include 5, 6, 7, 8, 9, 10, and 11mm.

If you plan to change coolant hoses this is a must have labor saving tool. This is one cleverly designed tool. Could not have done it better myself. I actually use to make a couple different types before I found this one. If you have ever tried to remove a radiator hose corroded to an aluminum housing you know what I am talking about and you will love this tool. Great when changing radiator hoses, especially the short hose. 8 inches in length.

It will get those stuck radiator hoses loose and off in seconds...

I like this - permanent - threadlocker because it is super strong but can still be removed with a heavy handed breaker bar. This is a very large bottle for the price and is a must have for Mercedes diesel owners. I use it anytime I am doing major repair work on an engine or transmission. Great for front crank bolt, cam bolt, torque converter bolts, injection pump mounting nuts, front engine accessories, brake caliper bolts, front suspension, etc. Anything that you can just not afford to come loose.

This removable thread locker is probably the best that I have used. It has the best sealing cap and cures rapidly and reliably when confined between metal parts. Use it to lock threaded fasteners, nuts, bolts and screws from loosening. Extremely important in critical engine and suspension parts. This is the removable type (meaning that it can be easily removed with hand tools). Comes in small .20 Fl oz. bottle great for most small jobs.

Excellent for all work around diesel engines to prevent vibration failure and breakdowns. If you need the red more permanent type CLICK HERE.

This permanent thread locker is probably the best that I have used. It has the best sealing cap and dries hard in 20 to 60 minutes. Use it to securely lock threaded fasteners, nuts, bolts and screws from loosening. Extremely important in critical engine and suspension parts. This is the permanent type (meaning that it is possible to remove only when applying heat to 450 degress F - with propane torch) or a very heavy breaker bar. I like to use this one on brake caliper bolts as it is such a critical bolt.

Excellent when retaining bearings and bearing races, freeze plugs, rocker arm and main bearing studs, etc. Can fill gaps up to .007 and assures positive controlled locking.

If you work around your Mercedes much this is a great tool to have. The quality is exceptional for the price. It will reset to measure in both inches and millimeters. For a limited time I will even include a spare button battery at no extra cost.

If you are going to test and tune your diesel fuel injectors this is a must have tool! It is the best way to determine the current thickness of the pressure adjusting shim washer in each injector and to help choose the proper replacement. We are committed to helping you service and overhaul this critical maintenance component.

As I have said elsewhere on this site, fuel injectors may be the most neglected maintenance item on the older Mercedes diesel engines. Just because they are working does not mean they are working well. And now with the cost of diesel fuel creeping up to $5.00 per gallon this is even more important than ever! You can work on your injectors yourself. It is not difficult, but you are going to need the right tools. I have put together this quality but inexpensive tool set for those who want to tune-up or overhaul their injectors on their own. If you are running SVO in your diesel you MUST take care of your injectors or your diesel will not take care of you. This tool set includes the following:

As I have said eslewhere on this site, fuel injectors may be the most neglected maintenance item on the older Mercedes diesel engines. Just because they are working does not mean they are working well. And now with the cost of diesel fuel creeping up to $5.00 per gallon this is even more important than ever! You can work on your injectors yourself. It is not difficult, but you are going to need the right tools. I have put together this quality but inexpensive tool set for those who want to tune-up or overhaul their injectors on their own. If you are running SVO in your diesel you MUST take care of your injectors or your diesel will not take care of you. This tool set includes the following:

If you are installing a dual tank conversion in your Mercedes you are going to need a way to allow the hoses to enter the trunk somewhere. The best way to do this is to use a hole saw to cut one or two round holes in the spare tire will in bring in the coolant hoses and/or fuel hoses. The hoses can be protected from chaffing with tape and then sealed with Silicone to prevent water and dirt from entering your trunk. Yes, I know these hole saws are not meant for metal - and that is why you need this cheap set. No need to dull your expensive hole saws. Once or twice on metal and the saws are done. But then you wont be using all the sizes in this kit so you will end up with extras for future wood projects around the house.

Here is an inexpensive set of cleaning brushes that really get down in the crevices. The plastic one is good for exterior cleaning around the window and body trim. The brass is good for cleaning engine parts you don't want to scratech. The steel one is excellent if you are doing some rust repair.

This shim kit is for those who want a large assortment of every possible combination at their fingertips. It is not easy to find such a complete kit. I personally looked so long to find a good source that I finally gave up and am now importing this high quality master mechanic shim kit directly from Germany. Each shim is extremely accurate in thickness. The shim washers are 11.5 mm in diameter and will work on all Mercedes passenger car diesels from 1958 to 1993.

If you are going to work on your diesel fuel injectors you are going to need a torque wrench. If you are going to tighten your alloy wheel lug bolts properly you should use a torque wrench. In fact if you do your own work you should have a 1/2 inch clicker torque wrench in your tool box. I know why you don't have one. They tend to be expensive for the limited amount you might use one. Well, now you can get a quality one for a very good price. This is a special offer and we only have a limited number in stock.

It comes with a nice moulded plastic case and instructions. This wrench is 18 inches long for good hand torque and it is made in Taiwan. Much better quality than those made in China.

 

From all my years of working around engines the one thing that absolutely drives me crazy is barbed hose fittings. This even got worse in recents years as many SVO WVO kit makers would send our their components with barbed hose fittings! Just try to remove a rubber fuel hose from a barbed fitting after is has been clamped down, or not even clamped down. Try to remove it after a few months when the hose has been heated and it is even worse!. You end up having to cut the hose off and if you are not careful you can nick the barb and the new hose will leak.

In all my years of working around engines the one thing that absolutely drives me crazy is barbed hose fittings. This even got worse in recents years as many SVO WVO kit makers would send our their components with barbed hose fittings! Just try to remove a rubber fuel hose from a barbed fitting after is has been clamped down, or not even clamped down. Try to remove it after a few months when the hose has been heated and it is even worse!. You end up having to cut the hose off and if you are not careful you can nick the barb and the new hose will leak.

When it comes to cleaning diesel fuel injectors, and yes they do need periodic cleaning, there is nothing like having the right tools to do the job. After cleaning literally hundreds of diesel injectors and nozzles I decided to come up with my own set of special brass tools and share them with our customers.

This tool set will help you disassemble and clean the internal parts without damaging the critical sealing surfaces and injector needle and seat surfaces. Only brass tools should be used on internal parts. The kit contains brass brushes, a brass scraper, a brass seat cleaner, a brass sump chamber cleaning, a brass nozzle hole cleaning, and aluminum vise protectors. I even throw in a stainless steel and nylon brush to help clean the outside surfaces. Patent Pending.

Almost all Mercedes gas and diesel engines from the late 50's up to the early 90's used pressed in steel pins to hold the timing chain guide rails in position (inside the engine block). To easily remove these you can use a slide hammer IF the engine is out of the car!!! In the real world of old cars, timing chain guide rails often have to be replaced with the engine in the car! There is no room between the front of the engine and the radiator to get any type of slide hammer or long puller tool to work.

If you are looking for an inexpensive way to test the electrical circuits on your Mercedes here is a good option. This tester reads both AC and DC voltage, DC current, resistance, and transistor, diode and battery test. Features automatic zero adjust, overange indication, and low battery indicator. Easy to read LCD readout and comes with 32 inch long test leads. Great for testing battery drains and glow plugs.

If you plan to do much work on your Mercedes these metric wrenches and sockets are very desireable - if not a necessity. If you have wanted to add to your tool box but not spend a lot of money here is your chance. These are not Snap On quality wrenches but if you only work on cars ocassionally these are more than adequate to get the job done. Set includes metric crows feet, metric 3/8 inch drive hex (Allen) sockets, and metric 1/4 inch drive socket set 5 to 14 mm. These items are also available separately. To see a list of all our tools CLICK HERE.