Ponton

These are the zip ties we have all been looking for. They have a super sticky tape of the foot of the tie so you can stick them anywhere in your engine compartment without having to drill a hole in the inner fender panel. (NOTE: Be sure to thoroughly clean the surface BEFORE installing). The other neat thing is that these zip ties can be loosened back up (just like the factory type) to remove the wire bundle or anything else you need to secure. Sold in packs of 6. You will love these!

This is the tool I love to use when troubleshooting engine operating temperature problems. You can stand back and aim the beam right on a spot on the radiator or engine to get an exact temperature reading. This can indicate whether or not your radiator is plugged and confirm if your temperature gauge is accurate or not.

If you are running SVO it can give you accurate readings of the temperature of your oil - both during filtering and coming out of your boost heater.

Features:

Used Webasto sunroof assembly with cross bars and chrome handle as shown. Bars and mechanism are good but fabric will need to be replaced of course.

NEW LOCTITE PRODUCT - AUGUST PROMO! If you have read very many of my manuals and instructions you already know how much I detest Silicone Gasket Sealant. I know there are places for silicone (ie bath tub caulking, etc), but it should not be used on internal combustion engines!

Applies to all Mercedes, PON FIN Pre 1960, 190SL, 110, 111, 112, 113, 114, 115, 108, 109, 107, 116, 123, 126, 201, and 124 chassis. Here is a kit you will love to have around the shop. If you don't like using those poor quality US hose clamps (the kind that cut into the hose) then here is a chance to have spare quality (no nick) hose clamps for those fuel and coolant related repairs. Kit comes with  large size hose clamp. Hose clamp size is 32-50/9.

Applies to all Mercedes, PON FIN Pre 1960, 190SL, 110, 111, 112, 113, 114, 115, 108, 109, 107, 116, 123, 126, 201, and 124 chassis. Here is a kit you will love to have around the shop. If you don't like using those poor quality US hose clamps (the kind that cut into the hose) then here is a chance to have spare quality (no nick) hose clamps for those fuel and coolant related repairs. Kit comes with 10 medium size hose clamp. Hose clamp size is 16-27/9.

Great to carry in trunk for emergencies. Nice case. No instructions included with this kit. Bulbs are applicable to most models from the early 70's to late 80's.

This kit includes:

This bulb is a single element bulb that is used in the brake light, rear turn signal and your rear back up lens. It's a very universal bulb. Fits mid 60s to 90s Mercedes.

This is a 3 piece scribe and pick tool set - great for marking aluminum and steel.

Heat shrink tubing is very handing to have if you are doing any wire connections or splicing. This tubing can go over the splice or solder joint and when heat is applied from a heat gun it will shrink right down tight to the joint and protect it from shorts and corrosion.

This circuit tester has a long 7 inch point to get into hard to reach places. Accordion cord extends up to 12 feet! Wow!

This is a set of metric nut drivers. It come in 7 different handy sizes and is even color coded. Sizes include 5, 6, 7, 8, 9, 10, and 11mm.

If you plan to change coolant hoses this is a must have labor saving tool. This is one cleverly designed tool. Could not have done it better myself. I actually use to make a couple different types before I found this one. If you have ever tried to remove a radiator hose corroded to an aluminum housing you know what I am talking about and you will love this tool. Great when changing radiator hoses, especially the short hose. 8 inches in length.

It will get those stuck radiator hoses loose and off in seconds...

I like this - permanent - threadlocker because it is super strong but can still be removed with a heavy handed breaker bar. This is a very large bottle for the price and is a must have for Mercedes diesel owners. I use it anytime I am doing major repair work on an engine or transmission. Great for front crank bolt, cam bolt, torque converter bolts, injection pump mounting nuts, front engine accessories, brake caliper bolts, front suspension, etc. Anything that you can just not afford to come loose.

This removable thread locker is probably the best that I have used. It has the best sealing cap and cures rapidly and reliably when confined between metal parts. Use it to lock threaded fasteners, nuts, bolts and screws from loosening. Extremely important in critical engine and suspension parts. This is the removable type (meaning that it can be easily removed with hand tools). Comes in small .20 Fl oz. bottle great for most small jobs.

Excellent for all work around diesel engines to prevent vibration failure and breakdowns. If you need the red more permanent type CLICK HERE.

This permanent thread locker is probably the best that I have used. It has the best sealing cap and dries hard in 20 to 60 minutes. Use it to securely lock threaded fasteners, nuts, bolts and screws from loosening. Extremely important in critical engine and suspension parts. This is the permanent type (meaning that it is possible to remove only when applying heat to 450 degress F - with propane torch) or a very heavy breaker bar. I like to use this one on brake caliper bolts as it is such a critical bolt.

Excellent when retaining bearings and bearing races, freeze plugs, rocker arm and main bearing studs, etc. Can fill gaps up to .007 and assures positive controlled locking.

If you work around your Mercedes much this is a great tool to have. The quality is exceptional for the price. It will reset to measure in both inches and millimeters. For a limited time I will even include a spare button battery at no extra cost.

If you are going to test and tune your diesel fuel injectors this is a must have tool! It is the best way to determine the current thickness of the pressure adjusting shim washer in each injector and to help choose the proper replacement. We are committed to helping you service and overhaul this critical maintenance component.

Here is an inexpensive set of cleaning brushes that really get down in the crevices. The plastic one is good for exterior cleaning around the window and body trim. The brass is good for cleaning engine parts you don't want to scratech. The steel one is excellent if you are doing some rust repair.

If you are going to work on your diesel fuel injectors you are going to need a torque wrench. If you are going to tighten your alloy wheel lug bolts properly you should use a torque wrench. In fact if you do your own work you should have a 1/2 inch clicker torque wrench in your tool box. I know why you don't have one. They tend to be expensive for the limited amount you might use one. Well, now you can get a quality one for a very good price. This is a special offer and we only have a limited number in stock.

It comes with a nice moulded plastic case and instructions. This wrench is 18 inches long for good hand torque and it is made in Taiwan. Much better quality than those made in China.

 

This is the first release from Kent Bergsmas new Advanced DIY Mechanic Series of repair manuals. This printed and wire bound guide will teach you everything you have ever wanted to know about how your pre-glow system works, how to quickly diagnose faults, how to repair and replace failed parts, how to prevent further problems, and how to upgrade a sluggish glow plug system.

The manual is printed in an 8.5 x 7 inch size and is 42 pages in length with 80 drawings, photos and illustrations. Knowing that this manual will be handled many times we have added a clear plastic front and back cover to minimize dirt and grease contamination. It is also printed on heavier 32 lb. bright white stock paper. Table of contents include:

Almost all Mercedes gas and diesel engines from the late 50's up to the early 90's used pressed in steel pins to hold the timing chain guide rails in position (inside the engine block). To easily remove these you can use a slide hammer IF the engine is out of the car!!! In the real world of old cars, timing chain guide rails often have to be replaced with the engine in the car! There is no room between the front of the engine and the radiator to get any type of slide hammer or long puller tool to work.

This is one of the best built fluid extractors I have seen. As is it works great for drawing power steering fluid, brake fluid, etc. out of their reservoirs. If you attach a hard plastic line on the end (you will need to fabricate a fitting reducer) you can even draw transmission and engine oil. It works great for extracting trans fluid when it has been overfilled. Can be used to add new fluids. You can add transmission fluid carefully to get just the right amount without spilling all over the place. :-)

There are nice measurng marks on the outside of the plastic tub. The pump rod is made from brass and both end caps are threaded aluminum (so you can remove them for cleaning and inspection.

If you are looking for an inexpensive way to test the electrical circuits on your Mercedes here is a good option. This tester reads both AC and DC voltage, DC current, resistance, and transistor, diode and battery test. Features automatic zero adjust, overange indication, and low battery indicator. Easy to read LCD readout and comes with 32 inch long test leads. Great for testing battery drains and glow plugs.

If you plan to do much work on your Mercedes these metric wrenches and sockets are very desireable - if not a necessity. If you have wanted to add to your tool box but not spend a lot of money here is your chance. These are not Snap On quality wrenches but if you only work on cars ocassionally these are more than adequate to get the job done. Set includes metric crows feet, metric 3/8 inch drive hex (Allen) sockets, and metric 1/4 inch drive socket set 5 to 14 mm. These items are also available separately. To see a list of all our tools CLICK HERE.

Long drive pin punches are very handy when working on your Benz. The smaller size in this set is particularly helpful when removing and replacing twin pin style brake pads. All steel. Made in India.

Not only does this set include almost 100 pieces but it includes metric sized allen (hex) bits and even an attachment to remove a wing nut! How cool is that? Most kits don't contain metric sizes. There are probably enough screwdriver bits in this kit to last you for a very long. Comes in nice molded red case.

Installing steel threaded spark plugs in aluminum heads is risky business. If you are not careful it is easy to damage the fragile aluminum threads. In a few cases I have seen spark plugs blow out of their holes while the engine is running. And does that ever make a loud racket! Heavy handed mechanics often cross thread the plugs during a tune-up and you wont even know it until you go to replace the plugs at some later date.

Great set of metric open end wrenches to get into those real tight places. Metric sizes from 10 to 19 mm. Made in India. They use the standard 3/8 inch drive extension as long as you need to work at right angles in restricted space. Only 10 sets available at this price!

Here is a great set of metric wrenches at a fantastic price that you can afford to cut, grind, heat and bend for all those instances where you need a specical wrench to get into a tight place. These are a black oxide finish so you won't have a problem with the chrome chipping or peeling off after modification. They are made in India and I have found they are a little tougher than the cheap sets coming out of China. Sizes range from 6 mm to 24 mm. The other nice thing about these wrenches is the open end heads are thinner than most other wrenches and will allow you to get onto narrower nuts. And if they are still too thick you can grind them thinner!!

Every tool box should have this set!

Fits Early Mercedes Ponton cars, both Gasoline and Diesel (including 190SL). Dimensions are 3 inches long with 1 and 3/16 inch inside diameter. If you recognize this hose right away, then you probably have been looking for it for quite some time! This is the very special flex rubber short hose located on the upper side of the radiator. This is a Genuine Mercedes OEM part that we have decided to source and carry for our Ponton customers.

SKU: CCP-PONRSH