How to Hook Up and Read a Kjet Fuel Pressure Tester - On Demand Video
In this 26 minute instructional video Kent will show you how to hook up a CIS fuel pressure tester to your older K-jectronic gas engine.
Kent's Factory Service Manuals collection is going on sale now. CLICK HERE.
In this 26 minute instructional video Kent will show you how to hook up a CIS fuel pressure tester to your older K-jectronic gas engine.
In this 10 minute instructional video Kent will explain why you want to "jump" your K-jet fuel pump relay, how to do it, how to find the location in you car, and why he prefers to have a long "switchable" jumper.
This xx minute video will take you step by step through the process of modifying your warm up regulator so you will be able to easily make adjustments to your cold start control pressure.
This 33 minute video will instruct you on how to replace the fuel injectors in your 8-cylinder M116 engine safely and efficiently. This is a fairly straightforward job, but there are some pitfalls you will want to avoid.
In part one Kent will show you how to get all the sunroof parts off our old Mercedes and on a bench particularly if you sunroof is broken and not moving. In this 21 minute instructional video here is a list of the subjects he covers:
Is your old gas engine running a little rough? There could be lots of reasons for this but if you have good compression, good plugs and wires you might consider replacing your O2 sensor even if your warning light is not showing up. This is an easy DIY job.
In this 13 minute instructional video Kent will demonstrate how to remove an old fan clutch and replace it with a new one on a 1983 380SL This is a beginner D.I.Y. job and no special tools are required. This video is included free of charge with the purchase of our Later V8 fan clutch kit.
In this detailed 30-minute video Kent will walk you through the process of installing new tie rod ends on his 1959 Mercedes 220SE. The principles are the same on almost all models from the 1950s up to the 1990s. He will explain the differences in adjustment between the older and newer styles
Kent delivers a very detailed 24 minute video on understanding how this valve works and how to fix it if possible. You will learn how to recognize a valve that is just too worn out to repair. No bleeder valve repair parts are available and there is not way to DIY fix one if it is badly damaged.
In this 30-minute instructional video, Kent will explain how this new pump compares to the original, what is included in the kit and why, how to make a new plugin wiring harness, demonstrate step by step how to install this pump in a late W123 and explain the differences you will face when instal
In this 17 minute instructional video Kent will walk you through removing and installation a VCV valve off the back of the injection pump and the proper way to adjust the linkage travel for best performance. A number of tips will be shared to reduce frustration and prevent problems.
This video ONLY covers some of Kent's "tips and tricks" on installing a harmonic balancer back onto the front of the crankshaft on an old Mercedes engine. The specific procedure was filmed while doing a front crank seal replacement on a 1983 240D.
In this 16-minute instructional video, Kent will explain some of the challenges and problems you may have to deal with when changing your instrument cluster bulbs by not removing the cluster.
To many people, automotive electrical systems and testing are a big mystery. It is not as complicated as you might think.
In this video, Kent will show you how he fixed his leaking tires on his chrome alloy wheels by using Miracle Paint. This is a full 22-minute step-by-step instructional video. Watch the video "trailer" below to give you a better understanding of what is involved in this procedure.
This 25-minute video is a supplement to Kent's other instructions on replacing diesel engine front crank seals. It is offered free of charge with one of the seal replacement kits.
In this video Kent will share some set up tips as well as explain what is in the compression tester and an overview of how it is used.
This video will show you how to remove the front crank seal race using the factory tool and using Kent's custom puller. It will also demonstrate a very easy way to install a new replacement race before installing a new seal.
Kent will get right up behind the rear end hub plate and show you close up how to remove and replace a sway bar link. This is not a difficult job especially if you follow the sequence shown in this 7- minute video.
In this 30 minute-long video Kent will walk you through what he did for the rear suspension on his 1983 240D.
In this 46 minute very detailed step-by-step video instruction, Kent will show you how to remove the fuel delivery system from your 1986 to 1991 420SEL, 300SE, 300SEL, 560SEL, 560SL, and 560SEC, take it over to your bench and take it all apart, install new pumps, filter, accumulator, and hoses, t
This 17-minute video will cover the removal of an old Hirschmann power antenna and then Kent will show you how to troubleshoot the wiring plug in the car to see if you are getting proper power back to the antenna. No sense in replacing a faulty antenna until you make sure your wiring is OK!
In this xx-minute long video, Kent will show you how to install our aftermarket power antenna in your 116, 123, or 123 sedan or coupe. Removal of your old antenna is not covered in this on-demand video but it is very straightforward once you remove the inner fender well panel.
You might be surprised to realize you spark plug holes need cleaning - and yes some REALLY need cleaning! This 5-minute video will demonstrate Kent's method of cleaning the threads in the cylinder.
This video will walk you step-by-step through the proper procedures for doing a full compression test on your older V8 Mercedes Engine.
This video is loaded with tips on how to properly lubricate all the key components that make your sunroof operate smoothly and properly. It is NOT a complete manual on everything related to sunroofs. It will NOT show you all the details to get the sunroof out and back in.
In this 22-minute instructional video, Kent will take you inside the door on a W123 240D and show you all the key points that should be lubricated and the type of lubricants you should use.
This is a very common problem on the W123. The wood will just fall off someday. Worse when the car is left outside or in a hot climate.
Replacing a distributor cap is easy right. No problem?? If it were I would not get so many emails and why the engine won't run right after changing the cap and rotor. This is a short eight and a half minute video but the tips I share could save you some big headaches.
This on-demand instructional video was filmed to go with Kent's new fuel tank sending unit service kit launched in June of 2020. This is not a complete video on the subject of fuel level sending units. For the complete video see related products below.
This 11-minute instructional video will show you how to set up and use a digital tach to check the idle speed of your diesel engine and how to use the tools in Kent's kit to adjust the idle speed on 1977 to 1985 four and five-cylinder diesels ( not 190D ).
This 23-minute video will demonstrate how Kent repairs some small rust spots inside the fender wells of a W116 sedan. Disclaimer: This method of repair is not recommended for large rust holes under the car or for holes that have been caused by road salt.
When the motor won't move the window down you can not get to the bolts that hold the regulator to the glass. So then how can you get it out of the door! What a pain! In this xxx minute video Kent will show you what you need to do in order to get a "stuck" power window regulator out of a door.
PLEASE read the instructions below carefully on how you will view this video. It is NOT downloaded to your computer and viewing is NOT automatic. You must be logged in at Mercedessource.com and you MUST click on "my account".
In this video, Kent will show you how to safely and cleanly remove the fuel from the tank on your older Benz. You will need to drain the fuel anytime you replace the back end hoses, the tank filter screen, the fuel pump or the fuel filter.
In this video, Kent will walk you through the steps needed to convert your older Brake Bleeder tank to one that can continue to bleed brake systems as well as pressure test radiators and cooling systems.
If you are experiencing hard starting or unexplained loss of power, your engine's lift pump could be failing.
This on-demand video will take you through the process of replacing the worn-out ball joint bushings that connect to the front suspension guide rod on all W126 sedans and couple built from 1980 to 1991. This video comes free of charge when you purchase our complete repair kit.
Published in August of 2019, this has been one of the most requested videos over the past two previous years.
This video will cover the use of my custom plastic tool to safely remove the steel center section for the outside aluminum housing with rebuilding your older style SLS ( Self Leveling Suspension) hydraulic pump. No other instructions included here.
This video will not only save the condition of your door panel, but it will save you a lot of time and frustration when you go to replace a door panel after doing maintenance inside your door. Those old plastic film liners always seem to be torn, ripped, and downright ugly.
This video is specifically for setting up and using Kent's newest version of his diesel fuel injector bench mount tester. It does not contain any information on the actual process of cleaning or rebuilding a fuel injector.
This video is part of the full net repair kit we sell. See related products below. If you choose just to watch this video, you will have to source your own bungee cord and crimping sleeves.
This on demand video only covers the principles of how to get a non-memory power seat in a 1980 to 1990 Mercedes to move forward and backward so you can get to the bolts to remove the seat from the car or remove the seat spring from the track assembly.
Our seat spring repair kit has been a great success! It can easily repair sagging on broken front seat springs. But what about seat padding. A lot of the older ( 1970's to 1980's glued fiber seat padding can crush down and even disintegrate over time.
This video will show Kent's technique on how to prime and paint alloy wheels using our wheel paint kit and masking dam that we sell separately. See below. The techniques will also apply to any spray can paint you should choose to use.
This is a full 25-minute step-by-step instructional video on how to properly flush or bleed your brake system using our pressure brake bleeder and fluid capture tank.
In this video, Kent explains the correct procedure for cleaning and lubricating your hubs and rear brake rotor BEFORE you install your wheels. He hardly ever sees this done when removing wheels on 15 plus-year-old Mercedes so he knows it is almost ALWAYS neglected.
Kent came up with this kit because of all the times he replaced e-brake shoes only to end up with battered knuckles and extreme headaches. This video is included free with the purchase of the toolkit.
This video is intended to be used as instructions when purchasing Kent's Rust Buster Tool. It can be viewed separately but you will need the tool to apply the principles. This video is included free of charge when purchasing the tool. See related products below: