Electrical

IMPORTANT NOTE: We do not sell replacement antenna masts by year and model. We have run across too many problems with confusion, interchangeability, and previously swapped antennas. We sell a SMOOTH TAIL mast and a TOOTHED TAIL mast. Smooth tails were used on most of the power Hirschmann antennas up to the early 80's and tooth tails were used on the later masts. For you to order the proper one you must partially remove your current mast and inspect. Is the white plastic tail more or less smooth or does it have teeth in it? The one describe here is the TOOTHED style.

CLICK HERE to view the smooth style.

When was the last time you knocked one of your vacuum lines off around the oil fiter housing, only to discover when you tried to reattached it that the fittings were swollen and would just not stay connected? This is a + shaped fitting that fits 115, 116, 123, and 126 chassis.

New Glow Plug Relay. Fits ONLY 1975 and 1976 115 chassis 300D.

Complete R134a retrofit kit as shown to convert your A/C system.  Keep in mind this may not repair all problems with your current A/C system. This kit is designed to go into a good working system. There maybe other parts you will want to purchase such as receiver dryer, etc while doing this conversion. Consult with your local A/C specialist if you are unfamiliar with air conditoning systems.

PLEASE NOTE: We are supplying this inexpensive kit as a convenience to our customers. It will not come with detailed instructions nor do we offer support on how to convert your current system. That will be between you and your local A/C specialist.  

5 handy bulbs to carry in your trunk for emergencies.  2 single element for turn signal, brake light or backup lights. 2 small single element for tail light running lights (correct size and watts to prevent melting plastic). 1 twin element bulb for from marker / turn signal lens.

Fits almost all models from the early 1970s to the mid 1990s

This bulb is a single element bulb that is used in the brake light, rear turn signal and your rear back up lens. It's a very universal bulb. Fits mid 60s to 90s Mercedes.

These dash light bulbs are small in size and fit a number of dash light applications behind your instrument cluster and in your center dash console.

These small frosted light bulbs are 1.2 watts and fit applications where you want a dimmer light ie, heater control knob 240D and some other center dash lights.

These bulbs are 5 watts and they fit a number of applications for instance in your instrument cluster. Check to see how many you need.

These bulbs dont neccessary fit all models. This bulb is 1 5/8 inch long. Some applications require smaller bulbs, please measure your bulb before ordering this 6 pak.

These are correct Osram small diameter bulbs for your rear tail light. Use this bulb to prevent over heating of the lens. Comes in a 6 bulbs set.

This is a set of 6 front turn signal light bulbs. Fits early 70s to mid 90s Mercedes.

Heat shrink tubing is very handing to have if you are doing any wire connections or splicing. This tubing can go over the splice or solder joint and when heat is applied from a heat gun it will shrink right down tight to the joint and protect it from shorts and corrosion.

Good used black visor mirror clip for late 123 chassis with lighted mirrors on the visors. This one has good electrical contacts and is not broken. We also have in blue and palomino. Email us.

Set of left and right 110 chassis bulb holders.  Only fits early models up to 1965.  No perfect but no heavy corossion or rust. Set of left and right side

Fits chassis 116 123 126 and 201 Diesels with PENCIL glow plugs, from 1978 to 1989. This little strip fuse is located in the Glow Plug Relay and can sometimes be the cause of your glow plug problems. Even if it appears to be good, we recommend that you physically remove it and inspect it for cracks or breaks before you replace the Relay! Sold in a 2 pack.

 

High performance glow plug set (6 total) for your E300D. Only fit 210 chassis 1996 to 1999. Made by Monark in Germany. Not Bosch in France or Turkey! Now long reach glow plugs for a great price that really are hot!

Set of 5 High Quallity German made Monark Glow Plugs complete with a detailed manual written by Kent Bergsma. Many who own these cars complain they don't even know where the glow plugs are and are worried they could never replace them on their own. A shop will charge you a lot of money to do this job. It is time consuming but not rocket science. You have to remove the intake manifold on this engine to get the plugs replaced. My step by step illustrated manual with take you completely through the correct process. Glow plugs even come with locking nuts. These glow plugs also fit 1989 190D 2.5 (only 1989!)

To complete successfully you will need a new intake manifold gasket. CLICK HERE to order.

Application: Fits all 5 cylinder diesel engines 300SD from 1978 to 1985 and all 300D, 300CD and 300TD from 1980 to 1985 with pencil glow plugs. We have been so impressed with Monark Products that we have recently begun using their glow plugs. They are actually one of the last quality glow plugs still made in Germany. Even Bosch now makes their glow plugs in France, Turkey and other locations in Europe. Now don't get me wrong - Bosch is still a good product. But these Monark glow plugs are superb. They are built with the same materials and have the same specifications as the Duraterm pencil plugs. Even comes with 5 high quality locking nuts for the wires.

Application: Fits all 4 cylinder 240D diesel engines from 1980 to 1983 with pencil glow plugs. We have been so impressed with Monark Products that we have recently begun using their glow plugs. They are actually one of the last quality glow plugs still made in Germany. Even Bosch now makes their glow plugs in France, Turkey and other locations in Europe. Now don't get me wrong - Bosch is still a good product. But these Monark glow plugs are superb. They are built with the same materials and have the same specifications as the Duraterm pencil plugs. Even comes with 4 high quality locking nuts for the wires.

FITS THE FOLLOWING: 115, and 123 chassis, 1975 to 1979 5 cylinder non-turbo diesel engines with series (looped style) glow plugs installed. WARNING: Be sure to check that your glow plugs have not been changed to the parallel (pencil)fast glow type.

Glow plugs do not last forever. I have found they generally need to be replaced about every 2 to 3 years for peak performance. If your diesel starts hard when cold, or starts but runs rough for 30 to 60 seconds before smoothing out, or the glow dash light flashes right after startup, then it may be time to replace the glow plugs. They should be replaced in sets unless you have the odd failure of just one fairly new plug.

FITS THE FOLLOWING: 110, 115, and 123 chassis, 1965 to 1979 4 cylinder diesel engines with series (looped style glow plugs installed. WARNING: Be sure to check that your glow plugs have not been changed to the parallel (pencil) fast glow type.

Glow plugs do not last forever. I have found they generally need to be replaced about every 2 to 3 years for peak performance. If your diesel starts hard when cold, or starts but runs rough for 30 to 60 seconds before smoothing out, or the glow dash light flashes right after startup, then it may be time to replace the glow plugs. They should be replaced in sets unless you have the odd failure of just one fairly new plug.

Cleaning out your glow plug holes from excess carbon (coke) can increase fuel economy and will extend the life of your glow plugs. This important regular maintenance procedure is commonly neglected and will lead to rough starts, smoke at startup, decreased fuel economy, and engine shake.

Cleaning out your glow plug holes from excess carbon (coke) can increase fuel economy and will extend the life of your glow plugs. This important regular maintenance procedure is commonly neglected and will lead to rough starts, smoke at startup, decreased fuel economy, and engine shake.

Fits all 123 Chassis from 1977-1985, gas and diesel models with automatic transmission. There is a small light bulb that fits down in your shifter just below the indicator cover. At night it lights up the indicator so you can see what gear you are in. Many times this bulb is burned out, and makes it difficult to shift at night! Sorry no instructions included.

Good used Bosch H4 headlight with flat face design. Only one. Does not include H4 bulb. If you are using these headlights you know how great they are!  May want to pick up a spare in case one of yours gets broken by a rock - and it does happen!

Bosch rebuilt Alternator fits 1978 to 1985 300SD and 1982 to 1985. If you have wanted to order one but did not have or want to pay for the core then we have one left in stock. You are welcome to purchase it with no core charge and no need to return your old alternator.

PLEASE NOTE: DOES NOT come with pulley or fan. You must use those from your existing alternator.

This is the first release from Kent Bergsmas new Advanced DIY Mechanic Series of repair manuals. This printed and wire bound guide will teach you everything you have ever wanted to know about how your pre-glow system works, how to quickly diagnose faults, how to repair and replace failed parts, how to prevent further problems, and how to upgrade a sluggish glow plug system.

The manual is printed in an 8.5 x 7 inch size and is 42 pages in length with 80 drawings, photos and illustrations. Knowing that this manual will be handled many times we have added a clear plastic front and back cover to minimize dirt and grease contamination. It is also printed on heavier 32 lb. bright white stock paper. Table of contents include:

Need an easy to install and quick solution for your worn out 201 heater motor?  Maybe brushes won't solve the problem. Maybe the bearings or commutator are just worn out. Although not cheap, installation is quick with this complete new OE Unit. This will fit all 201 models from 1984 to 1993. If you have not replaced one before I would highly recommend my instruction booklet. CLICK HERE to order the manual.

IMPORTANT NOTE: We do not sell replacement antenna masts by year and model. We have run across too many problems with confusion, interchangeability, and previously swapped antennas. We sell a SMOOTH TAIL mast and a TOOTH TAIL mast. Smooth tails were used on most of the power Hirschmann antennas up to the early 80's and tooth tails were used on the later masts. For you to order the proper one you must partially remove your current mast and inspect. Is the white plastic tail more or less smooth or does it have teeth in it? The one describe here is the SMOOTH style. CLICK HERE to view the toothed style.